69.99 mhz saw filter 0.8 mhz bandwidth part number sf0070cd03108s spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0070CD03108T rev a 16-feb-2010 ecn 36650 page 1 of 3 description ? 69.99 mhz saw bandpass filter with 0.8 mhz bandwidth. ? 73.3 x 20 mm dip package. ? rohs compliant. typical performance horizontal: frequency : 0.5 mhz/div vertical from top: relative magnitude : 10 db/div relative magnitude : 1 db/div phase linearity : 6 deg/div wideband response (0- 800 mhz, 10 db/div)
69.99 mhz saw filter 0.8 mhz bandwidth part number sf0070cd03108s spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0070CD03108T rev a 16-feb-2010 ecn 36650 page 2 of 3 specification parameter min typ max units center frequency 1 69.94 69.99 70.04 mhz insertion loss 2 - 17.5 19 db 1.5 db bandwidth 3 0.8 0.84 - mhz 40 db bandwidth 3 - 1.15 1.2 mhz amplitude ripple 4, 5 - 0.4 1.0 db p-p absolute delay - 8.82 - s phase linearity 4 - 3.5 6 deg p-p rejection, 10 mhz to 69.09 mhz 3 50 56 - db rejection, 70.89 mhz to 71.19 mhz 3 45 51 - db rejection, 71.19 mhz to 130 mhz 3 50 57 - db rejection, 130 mhz to 800 mhz 3 45 56 - db input return loss 4, 6 10 15 - db output return loss 4, 6 10 15 - db source and load impedance - 50 - ? ambient temperature - 25 - ? c notes: 1. average of lower and upper 3db point s (3db is relative to the insertion loss). 2. measured at the point in the passband where the loss is a minimum. 3. all stated db levels are relative to the insertion loss. 4. over 0.8 mhz bandwidth. 5. defined as maximum level ? minimum level over the given bandwidth, excluding the band edges. 6. when matched externally, as shown below. maximum ratings parameter min max units storage temperature range -40 85 ? c operating temperature range -40 85 ? c input power level - 20 dbm matching circuit typical component values: (minimum inductor q = 40) notes: 1. required component tolerances: inductors +/-2%, capacitors +/-5%. 2. component values shown are for guidance only and may change depending on board layout. ls1 = 150 nh ls2 = 150 nh cp1 = 100 pf cp2 = 120 pf input 50 ? single-ended output 50 ? single-ended 2 11 1,3,4,5,6,7,8,9,10,12, 13,14,15,16,17,18
69.99 mhz saw filter 0.8 mhz bandwidth part number sf0070cd03108s spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0070CD03108T rev a 16-feb-2010 ecn 36650 page 3 of 3 package outline iso 9001 registered all specifications are believed to be accurate and reliable. howe ver, spectrum microwave reserves the right to make changes wit hout notice. ? 2010 all rights reserved. units: mm tolerances are 0.15 mm except for the overall length and width, which are nominal values. pad configuration: input: 2 output: 11 ground: all other pins
|